init.c

Go to the documentation of this file.

/* FreeEMS - the open source engine management system
 *
 * Copyright 2008, 2009, 2010 Fred Cooke
 *
 * This file is part of the FreeEMS project.
 *
 * FreeEMS software is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * FreeEMS software is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with any FreeEMS software.  If not, see http://www.gnu.org/licenses/
 *
 * We ask that if you make any changes to this file you email them upstream to
 * us at admin(at)diyefi(dot)org or, even better, fork the code on github.com!
 *
 * Thank you for choosing FreeEMS to run your engine!
 */


#define INIT_C
#include "inc/freeEMS.h"
#include "inc/interrupts.h"
#include "inc/utils.h"
#include "inc/commsISRs.h"
#include "inc/pagedLocationBuffers.h"
#include "inc/init.h"
#include <string.h>


void init(){
    ATOMIC_START();             /* Disable ALL interrupts while we configure the board ready for use */
    initPLL();                  /* Set up the PLL and use it */
    initIO();                   /* TODO make this config dependent. Set up all the pins and modules to be in low power harmless states */
    initAllPagedRAM();          /* Copy table and config blocks of data from flash to the paged ram blocks for fast data lookup */
    initVariables();            /* Initialise the rest of the running variables etc */
    initFlash();                /* TODO, finalise this */
    initECTTimer();             /* TODO move this to inside config in an organised way. Set up the timer module and its various aspects */
    initPITTimer();             /* TODO ditto... */
    initSCIStuff();             /* Setup the sci module(s) that we will use. */
    initConfiguration();        /* TODO Set user/feature/config up here! */
    initInterrupts();           /* still last, reset timers, enable interrupts here TODO move this to inside config in an organised way. Set up the rest of the individual interrupts */
    ATOMIC_END();               /* Re-enable any configured interrupts */
}


/* used to chop out all the init stuff at compile time for hardware testing. */
//#define NO_INIT


void initPLL(){
    CLKSEL &= PLLSELOFF;    /* Switches to base external OSCCLK to ensure PLL is not being used (off out of reset, but not sure if the monitor turns it on before passing control or not) */
    PLLCTL &= PLLOFF;       /* Turn the PLL device off to adjust its speed (on by default out of reset) */
    REFDV = PLLDIVISOR;     /* 16MHz / (3 + 1) = 4MHz Bus frequency */
    SYNR = PLLMULTIPLIER;   /* 4MHz * (9 + 1) = 40MHz Bus frequency */
    PLLCTL |= PLLON;        /* Turn the PLL device back on again at 80MHz */

    while (!(CRGFLG & PLLLOCK)){
        /* Do nothing while we wait till the PLL loop locks onto the target frequency. */
        /* Target frequency is given by (2 * (crystal frequency / (REFDV + 1)) * (SYNR + 1)) */
        /* Bus frequency is half PLL frequency and given by ((crystal frequency / (REFDV + 1)) * (SYNR + 1)) */
    }

    CLKSEL = PLLSELON;      /* Switches to PLL clock for internal bus frequency */
    /* from MC9S12XDP512V2.pdf Section 2.4.1.1.2 page 101 Third paragraph       */
    /* "This takes a MAXIMUM of 4 OSCCLK clock cylces PLUS 4 PLL clock cycles"  */
    /* "During this time ALL clocks freeze, and CPU activity ceases"            */
    /* Therefore there is no point waiting for this to occur, we already are... */
}


/* Configure all the I/O to default values to keep power use down etc */
void initIO(){
    /* for now, hard code all stuff to be outputs as per Freescale documentation,   */
    /* later what to do will be pulled from flash configuration such that all       */
    /* things are setup at once, and not messed with thereafter. when the port      */
    /* something uses is changed via the tuning interface, the confuration will be  */
    /* done on the fly, and the value burned to flash such that next boot happens   */
    /* correctly and current running devices are used in that way.                  */

    /* Turn off and on and configure all the modules in an explicit way */
    // TODO set up and turn off all modules (CAN,SCI,SPI,IIC,etc)

    /* Turn off the digital input buffers on the ATD channels */
    ATD0DIEN = ZEROS; /* You are out of your mind if you waste this on digital Inputs */
    ATD1DIEN0 = ZEROS; /* You are out of your mind if you waste this on digital Inputs (NOT-bonded, can't use) */
    ATD1DIEN1 = ZEROS; /* You are out of your mind if you waste this on digital Inputs */
    /* TODO Second half of ATD1 - can we disable this somehow */

    /* And configure them all for analog input */
    ATD0CTL2 = 0x80; /* Turns on the ADC block. */
    ATD0CTL3 = 0x40; /* Set sequence length = 8 */
    ATD0CTL5 = 0xB0; /* Sets justification to right, multiplex and scan all channels. */
    // TODO find out if this is the default (i suspect it is)
    // TODO look into sampling techniques

    /* And configure them all for analog input */
    ATD1CTL0 = 0x07; /* Sets wrap on 8th ADC because we can't use the other 8 */
    ATD1CTL2 = 0x80; /* Turns on the ADC block. */
    ATD1CTL3 = 0x40; /* Set sequence length = 8 */
    ATD1CTL5 = 0xB0; /* Sets justification to right, multiplex and scan all channels. */
    // TODO find out if this is the default (i suspect it is)
    // TODO look into sampling techniques

#ifndef NO_INIT
    /* Set up the PWM component and initialise its values to off */
    PWME = 0x7F; /* Turn on PWM 0 - 6 (7 is user LED on main board) */
    PWMCLK = ZEROS; /* The fastest we can go for all channels */
    PWMPRCLK = ZEROS; /* The fastest prescaler we can go for all channels */
    PWMSCLA = ZEROS; /* The fastest we can go */
    PWMSCLB = ZEROS; /* The fastest we can go */
    /* TODO PWM channel concatenation for high resolution */
    // join channel pairs together here (needs 16 bit regs enabled too)
    /* TODO Initialise pwm channels with frequency, and initial duty for real use */
    // initial PWM settings for testing
    /* PWM periods */
    PWMPER0 = 0xFF; // 255 for ADC0 testing
    PWMPER1 = 0xFF; // 255 for ADC1 testing
    PWMPER2 = 0xFF; // 255 for ADC1 testing
    PWMPER3 = 0xFF; // 255 for ADC1 testing
    PWMPER4 = 0xFF; // 255 for ADC1 testing
    PWMPER5 = 0xFF; // 255 for ADC1 testing
    PWMPER6 = 0xFF; // 255 for ADC1 testing
    PWMPER7 = 0xFF; // 255 for ADC1 testing
    /* PWM duties */
    PWMDTY0 = 0;
    PWMDTY1 = 0;
    PWMDTY2 = 0;
    PWMDTY3 = 0;
    PWMDTY4 = 0;
    PWMDTY5 = 0;
    PWMDTY6 = 0;
    PWMDTY7 = 0;


    /* Initialise the state of pins configured as output */
    /* Initialise to low such that transistor grounded things are all turned off by default. */
    PORTA = ZEROS; /* The serial monitor pin is on 0x40, and could cause problems if capacitance at the output is large when a reset occurs. */
    PORTB = ZEROS; /* Init the rest of the spark outputs as off */
    PORTE = 0x1F; /* 0b_0001_1111 : when not in use 0b_1001_1111 PE7 should be high PE5 and PE6 should be low, the rest high */
    PORTK = ZEROS;
    PORTS = ZEROS;
    PORTT = ZEROS; /* All pins in off state at boot up (only matters for 2 - 7) */
    PORTM = ZEROS;
    PORTP = ZEROS; // TODO hook these up to the adc channels such that you can vary the brightness of an led with a pot.
    PORTH = ZEROS;
    PORTJ = ZEROS;
    /* AD0PT1 You are out of your mind if you waste this on digital Inputs */
    /* AD1PT1 You are out of your mind if you waste this on digital Inputs */

    /* Initialise the Data Direction Registers */
    /* To outputs based on the note at the end of chapter 1.2.2 of MC9S12XDP512V2.pdf */
    DDRA = ONES; /* GPIO (8) */
    DDRB = ONES; /* GPIO (8) */
    DDRE = 0xFC; /* 0b_1111_1100 : Clock and mode pins PE0,PE1 are input only pins, the rest are GPIO */
    DDRK = ONES; /* Only 0,1,2,3,4,5,7, NOT 6 (7) */
    DDRS = ONES; /* SCI0, SCI1, SPI0 (8) */
    DDRT = 0xFC; /* 0b_1111_1100 set ECT pins 0,1 to IC and 2:7 to OC (8) */
    DDRM = ONES; /* CAN 0 - 3 (8) */
    DDRP = ONES; /* PWM pins (8) */
    DDRH = ZEROS; /* All pins configured as input for misc isrs (SPI1, SPI2) (8) */
    DDRJ = ONES; /* Only 0,1,6,7 are brought out on the 112 pin chip (4) */
    /* Configure the non bonded pins to output to avoid current drain (112 pin package) */
    DDRC = ONES; /* NON-bonded external data bus pins */
    DDRD = ONES; /* NON-bonded external data bus pins */
    /* AD0DDR1 You are out of your mind if you waste this on digital Inputs */
    /* AD1DDR1 You are out of your mind if you waste this on digital Inputs */
#endif
}


void initLookupAddresses(){
    IATTransferTableLocation = (void*)&IATTransferTable;
    CHTTransferTableLocation = (void*)&CHTTransferTable;
    MAFTransferTableLocation = (void*)&MAFTransferTable;
    TestTransferTableLocation = (void*)&TestTransferTable;
}


void initFuelAddresses(){
    /* Setup addresses within the page to avoid warnings */
    VETableMainFlashLocation        = (void*)&VETableMainFlash;
    VETableSecondaryFlashLocation   = (void*)&VETableSecondaryFlash;
    VETableTertiaryFlashLocation    = (void*)&VETableTertiaryFlash;
    LambdaTableFlashLocation        = (void*)&LambdaTableFlash;
    VETableMainFlash2Location       = (void*)&VETableMainFlash2;
    VETableSecondaryFlash2Location  = (void*)&VETableSecondaryFlash2;
    VETableTertiaryFlash2Location   = (void*)&VETableTertiaryFlash2;
    LambdaTableFlash2Location       = (void*)&LambdaTableFlash2;
}


void initPagedRAMFuel(void){
    /* Copy the tables from flash to RAM */
    RPAGE = RPAGE_FUEL_ONE;
    memcpy((void*)&TablesA, VETableMainFlashLocation,       MAINTABLE_SIZE);
    memcpy((void*)&TablesB, VETableSecondaryFlashLocation,  MAINTABLE_SIZE);
    memcpy((void*)&TablesC, VETableTertiaryFlashLocation,   MAINTABLE_SIZE);
    memcpy((void*)&TablesD, LambdaTableFlashLocation,       MAINTABLE_SIZE);
    RPAGE = RPAGE_FUEL_TWO;
    memcpy((void*)&TablesA, VETableMainFlash2Location,      MAINTABLE_SIZE);
    memcpy((void*)&TablesB, VETableSecondaryFlash2Location, MAINTABLE_SIZE);
    memcpy((void*)&TablesC, VETableTertiaryFlash2Location,  MAINTABLE_SIZE);
    memcpy((void*)&TablesD, LambdaTableFlash2Location,      MAINTABLE_SIZE);
}


void initTimingAddresses(){
    /* Setup addresses within the page to avoid warnings */
    IgnitionAdvanceTableMainFlashLocation           = (void*)&IgnitionAdvanceTableMainFlash;
    IgnitionAdvanceTableSecondaryFlashLocation      = (void*)&IgnitionAdvanceTableSecondaryFlash;
    InjectionAdvanceTableMainFlashLocation          = (void*)&InjectionAdvanceTableMainFlash;
    InjectionAdvanceTableSecondaryFlashLocation     = (void*)&InjectionAdvanceTableSecondaryFlash;
    IgnitionAdvanceTableMainFlash2Location          = (void*)&IgnitionAdvanceTableMainFlash2;
    IgnitionAdvanceTableSecondaryFlash2Location     = (void*)&IgnitionAdvanceTableSecondaryFlash2;
    InjectionAdvanceTableMainFlash2Location         = (void*)&InjectionAdvanceTableMainFlash2;
    InjectionAdvanceTableSecondaryFlash2Location    = (void*)&InjectionAdvanceTableSecondaryFlash2;
}


void initPagedRAMTime(){
    /* Copy the tables from flash to RAM */
    RPAGE = RPAGE_TIME_ONE;
    memcpy((void*)&TablesA, IgnitionAdvanceTableMainFlashLocation,          MAINTABLE_SIZE);
    memcpy((void*)&TablesB, IgnitionAdvanceTableSecondaryFlashLocation,     MAINTABLE_SIZE);
    memcpy((void*)&TablesC, InjectionAdvanceTableMainFlashLocation,         MAINTABLE_SIZE);
    memcpy((void*)&TablesD, InjectionAdvanceTableSecondaryFlashLocation,    MAINTABLE_SIZE);
    RPAGE = RPAGE_TIME_TWO;
    memcpy((void*)&TablesA, IgnitionAdvanceTableMainFlash2Location,         MAINTABLE_SIZE);
    memcpy((void*)&TablesB, IgnitionAdvanceTableSecondaryFlash2Location,    MAINTABLE_SIZE);
    memcpy((void*)&TablesC, InjectionAdvanceTableMainFlash2Location,        MAINTABLE_SIZE);
    memcpy((void*)&TablesD, InjectionAdvanceTableSecondaryFlash2Location,   MAINTABLE_SIZE);
}


void initTunableAddresses(){
    /* Setup addresses within the page to avoid warnings */
    SmallTablesAFlashLocation   = (void*)&SmallTablesAFlash;
    SmallTablesBFlashLocation   = (void*)&SmallTablesBFlash;
    SmallTablesCFlashLocation   = (void*)&SmallTablesCFlash;
    SmallTablesDFlashLocation   = (void*)&SmallTablesDFlash;
    SmallTablesAFlash2Location  = (void*)&SmallTablesAFlash2;
    SmallTablesBFlash2Location  = (void*)&SmallTablesBFlash2;
    SmallTablesCFlash2Location  = (void*)&SmallTablesCFlash2;
    SmallTablesDFlash2Location  = (void*)&SmallTablesDFlash2;

    /* TablesA */
    dwellDesiredVersusVoltageTableLocation    = (void*)&SmallTablesAFlash.dwellDesiredVersusVoltageTable;
    dwellDesiredVersusVoltageTable2Location   = (void*)&SmallTablesAFlash2.dwellDesiredVersusVoltageTable;
    injectorDeadTimeTableLocation             = (void*)&SmallTablesAFlash.injectorDeadTimeTable;
    injectorDeadTimeTable2Location            = (void*)&SmallTablesAFlash2.injectorDeadTimeTable;
    postStartEnrichmentTableLocation          = (void*)&SmallTablesAFlash.postStartEnrichmentTable;
    postStartEnrichmentTable2Location         = (void*)&SmallTablesAFlash2.postStartEnrichmentTable;
    engineTempEnrichmentTableFixedLocation    = (void*)&SmallTablesAFlash.engineTempEnrichmentTableFixed;
    engineTempEnrichmentTableFixed2Location   = (void*)&SmallTablesAFlash2.engineTempEnrichmentTableFixed;
    primingVolumeTableLocation                = (void*)&SmallTablesAFlash.primingVolumeTable;
    primingVolumeTable2Location               = (void*)&SmallTablesAFlash2.primingVolumeTable;
    engineTempEnrichmentTablePercentLocation  = (void*)&SmallTablesAFlash.engineTempEnrichmentTablePercent;
    engineTempEnrichmentTablePercent2Location = (void*)&SmallTablesAFlash2.engineTempEnrichmentTablePercent;
    dwellMaxVersusRPMTableLocation            = (void*)&SmallTablesAFlash.dwellMaxVersusRPMTable;
    dwellMaxVersusRPMTable2Location           = (void*)&SmallTablesAFlash2.dwellMaxVersusRPMTable;

    /* TablesB */
    perCylinderFuelTrimsLocation  = (void*)&SmallTablesBFlash.perCylinderFuelTrims;
    perCylinderFuelTrims2Location = (void*)&SmallTablesBFlash2.perCylinderFuelTrims;

    /* TablesC */
    // TODO

    /* TablesD */
    // TODO

    /* filler defs */
    fillerALocation  = (void*)&SmallTablesAFlash.filler;
    fillerA2Location = (void*)&SmallTablesAFlash2.filler;
    fillerBLocation  = (void*)&SmallTablesBFlash.filler;
    fillerB2Location = (void*)&SmallTablesBFlash2.filler;
    fillerCLocation  = (void*)&SmallTablesCFlash.filler;
    fillerC2Location = (void*)&SmallTablesCFlash2.filler;
    fillerDLocation  = (void*)&SmallTablesDFlash.filler;
    fillerD2Location = (void*)&SmallTablesDFlash2.filler;
}


void initPagedRAMTune(){
    /* Copy the tables from flash to RAM */
    RPAGE = RPAGE_TUNE_ONE;
    memcpy((void*)&TablesA, SmallTablesAFlashLocation,  MAINTABLE_SIZE);
    memcpy((void*)&TablesB, SmallTablesBFlashLocation,  MAINTABLE_SIZE);
    memcpy((void*)&TablesC, SmallTablesCFlashLocation,  MAINTABLE_SIZE);
    memcpy((void*)&TablesD, SmallTablesDFlashLocation,  MAINTABLE_SIZE);
    RPAGE = RPAGE_TUNE_TWO;
    memcpy((void*)&TablesA, SmallTablesAFlash2Location, MAINTABLE_SIZE);
    memcpy((void*)&TablesB, SmallTablesBFlash2Location, MAINTABLE_SIZE);
    memcpy((void*)&TablesC, SmallTablesCFlash2Location, MAINTABLE_SIZE);
    memcpy((void*)&TablesD, SmallTablesDFlash2Location, MAINTABLE_SIZE);
}


void initAllPagedAddresses(){
    /* Setup pointers to lookup tables */
    initLookupAddresses();
    /* Setup pointers to the main tables */
    initFuelAddresses();
    initTimingAddresses();
    initTunableAddresses();
}


void initAllPagedRAM(){
    /* Setup the flash block pointers before copying flash to RAM using them */
    initAllPagedAddresses();

    /* Copy the tables up to their paged RAM blocks through the window from flash */
    initPagedRAMFuel();
    initPagedRAMTime();
    initPagedRAMTune();

    /* Default to page one for now, perhaps read the configured port straight out of reset in future? TODO */
    setupPagedRAM(TRUE); // probably something like (PORTA & TableSwitchingMask)
}


/* Initialise and set up all running variables that require a non-zero start value here */
/* All other variables are initialised to zero by the premain built in code             */
void initVariables(){
    /* And the opposite for the other halves */
    CoreVars = &CoreVars0;
    DerivedVars = &DerivedVars0;
    ADCArrays = &ADCArrays0;
    ADCArraysRecord = &ADCArrays1;
    asyncADCArrays = &asyncADCArrays0;
    asyncADCArraysRecord = &asyncADCArrays1;
    currentDwellMath = &currentDwell0;
    currentDwellRealtime = &currentDwell1;

    injectorMainPulseWidthsMath = injectorMainPulseWidths0;
    injectorMainPulseWidthsRealtime = injectorMainPulseWidths1;
    injectorStagedPulseWidthsMath = injectorStagedPulseWidths0;
    injectorStagedPulseWidthsRealtime = injectorStagedPulseWidths1;

    mathSampleTimeStamp = &ISRLatencyVars.mathSampleTimeStamp0; // TODO temp, remove
    mathSampleTimeStampRecord = &ISRLatencyVars.mathSampleTimeStamp1; // TODO temp, remove
    RPM = &RPM0; // TODO temp, remove
    RPMRecord = &RPM1; // TODO temp, remove

    /* Setup the pointers to the registers for fueling use, this does NOT work if done in global.c, I still don't know why. */
    injectorMainTimeRegisters[0] = TC2_ADDR;
    injectorMainTimeRegisters[1] = TC3_ADDR;
    injectorMainTimeRegisters[2] = TC4_ADDR;
    injectorMainTimeRegisters[3] = TC5_ADDR;
    injectorMainTimeRegisters[4] = TC6_ADDR;
    injectorMainTimeRegisters[5] = TC7_ADDR;
    injectorMainControlRegisters[0] = TCTL2_ADDR;
    injectorMainControlRegisters[1] = TCTL2_ADDR;
    injectorMainControlRegisters[2] = TCTL1_ADDR;
    injectorMainControlRegisters[3] = TCTL1_ADDR;
    injectorMainControlRegisters[4] = TCTL1_ADDR;
    injectorMainControlRegisters[5] = TCTL1_ADDR;

    configuredBasicDatalogLength = maxBasicDatalogLength;

    // TODO perhaps read from the ds1302 once at start up and init the values or different ones with the actual time and date then update them in RTI
}


void initFlash(){
    FCLKDIV = 0x4A;                     /* Set the flash clock frequency    */
    FPROT = 0xFF;                       /* Disable all flash protection     */
    FSTAT = FSTAT | (PVIOL | ACCERR);   /* Clear any errors                 */
}


/* Set up the timer module and its various interrupts */
void initECTTimer(){

    // TODO rearrange the order of this stuff and pull enable and interrupt enable out to the last function call of init.


#ifndef NO_INIT
    /* Timer channel interrupts */
    TIE = 0x03; /* 0,1 IC interrupts enabled for reading engine position and RPM, 6 OC channels disabled such that no injector switching happens till scheduled */
    TFLG = ONES; /* Clear all the flags such that we are up and running before they first occur */
    TFLGOF = ONES; /* Clear all the flags such that we are up and running before they first occur */

    /* TODO Turn the timer on and set the rate and overflow interrupt */
//  DLYCT = 0xFF; /* max noise filtering as experiment for volvo this will come from flash config */ // just hiding a wiring/circuit issue...
    TSCR1 = 0x88; /* 0b_1000_1000 Timer enabled, and precision timer turned on */
    TSCR2 = 0x87; /* 0b_1000_0111 Overflow interrupt enable, divide by 256 if precision turned off */
//  PTPSR = 0x03; /* 4 prescaler gives .1uS resolution and max period of 7ms measured */
    PTPSR = 0x1F; /* 32 prescaler gives 0.8uS resolution and max period of 52.4288ms measured */
//  PTPSR = 0x3F; /* 64 prescaler gives 1.6uS resolution and max period of 105ms measured */
//  PTPSR = 0xFF; /* 256 prescaler gives 6.4uS resolution and max period of 400ms measured */
//  PTPSR = 0x7F; /* 128 prescaler gives 3.2uS resolution and max period of 200ms measured */
    /* http://www.google.com/search?hl=en&safe=off&q=1+%2F+%2840MHz+%2F+32+%29&btnG=Search */
    /* http://www.google.com/search?hl=en&safe=off&q=1+%2F+%2840MHz+%2F+32+%29+*+2%5E16&btnG=Search */
    /* www.mecheng.adelaide.edu.au/robotics_novell/WWW_Devs/Dragon12/LM4_Timer.pdf */

    /* Initial actions */
    TIOS = 0xFC; /* 0b_1111_1100 0 and 1 are input capture, 2 through 7 are output compare */
    TCTL1 = ZEROS; /* Set disabled at startup time, use these and other flags to switch fueling on and off inside the decoder */
    TCTL2 = ZEROS; /* 0,1 have compare turned off regardless as they are in IC mode. */
    TCTL3 = ZEROS; /* Capture off for 4 - 7 */
    TCTL4 = 0x0F; /* Capture on both edges of two pins for IC (0,1), capture off for 2,3 */

    // TODO setup delay counters on 0 and 1 to filter noise (nice feature!)
    //DLYCT = ??; built in noise filter

    /* Configurable tachometer output */
    PTMCPSR = fixedConfigs1.tachoSettings.tachoTickFactor - 1; // Precision prescaler - fastest is 1 represented by 0, slowest/longest possible is 256 represented by 255 or 0xFF
    MCCNT = ONES16; // init to slowest possible, first
    MCCTL = 0xC4; // turn on and setup the mod down counter
    MCFLG = 0x80; // clear the flag up front
#endif
}


/* Configure the PIT timers for their various uses. */
void initPITTimer(){
#ifndef NO_INIT
    /*  */
    // set micro periods
    PITMTLD0 = 0x1F; /* 32 prescaler gives 0.8uS resolution and max period of 52.4288ms measured */
    PITMTLD1 = 0x1F; /* ditto */
    /* http://www.google.com/search?hl=en&safe=off&q=1+%2F+%2840MHz+%2F+32+%29 Exactly the same as for ECT */

    // set timers running
//  PITLD0 = dwellPeriod;
    // enable module
    PITCFLMT = 0x80;
    // enable channels
    //PITCE = 0x03;
    // enable interrupt
//  PITINTE = 0x01;
    // clear flags
    //PITFLT = ONES;
#endif
}

/* Setup the sci module(s) that we need to use. */
void initSCIStuff(){
    /* The alternative register set selector defaults to zero */

    // set the baud/data speed
    SCI0BD = fixedConfigs1.serialSettings.baudDivisor;

    // etc

    /* Switch to alternative register set? */

    // etc

    /* Switch back again? */

    /*
     * 0 = LOOPS (normal two wire operation)
     * 0 = SCISWAI (Wait mode on)
     * 0 = RSRC (if loops=1, int/ext wiring)
     * 1 = M MODE (9 bit operation)
     * 0 = WAKE (idle line wakeup)
     * 0 = ILT (idle line type count start pos)
     * 1 = PE (parity on)
     * 1 = PT (odd parity) (minicom defaults to no parity)
     *
     * 00010011 = 0x13
     */
    SCI0CR1 = 0x13;

    /*
     * 0 = TIE (tx data empty isr disabled)
     * 0 = TCIE (tx complete isr disabled)
     * 1 = RIE (rx full isr enabled)
     * 0 = ILIE (idle line isr disabled)
     * 1 = TE (transmit enabled)
     * 1 = RE (receive enabled)
     * 0 = RWU (rx wake up normal)
     * 0 = SBK (send break off)
     *
     * 00101100 = 0x2C
     */
    SCI0CR2 = 0x2C;
}

/* TODO Load and calculate all configuration data required to run */
void initConfiguration(){
//  // TODO Calc TPS ADC range on startup or every time? this depends on whether we ensure that things work without a re init or reset or not.


    /* Add in tunable physical parameters at boot time TODO move to init.c TODO duplicate for secondary fuel? or split somehow?
     *nstant = ((masterConst * perCylinderVolume) / (stoichiometricAFR * injectorFlow));
     *nstant = ((139371764   * 16384            ) / (15053             * 4096        ));
     * OR
     *nstant = ((masterConst / injectorFlow) * perCylinderVolume) / stoichiometricAFR;
     *nstant = ((139371764   / 4096        ) * 16384            ) / 15053            ;
     * http://www.google.com/search?hl=en&safe=off&q=((139371764++%2F+4096+++++)+*+16384+++)+%2F+15053++++&btnG=Search */
    bootFuelConst = ((unsigned long)(masterFuelConstant / fixedConfigs1.engineSettings.injectorFlow) * fixedConfigs1.engineSettings.perCylinderVolume) / fixedConfigs1.engineSettings.stoichiometricAFR;

    /* The MAP range used to convert fake TPS from MAP and vice versa */
    TPSMAPRange = fixedConfigs2.sensorRanges.TPSOpenMAP - fixedConfigs2.sensorRanges.TPSClosedMAP;

    /* The ADC range used to generate TPS percentage */
    TPSADCRange = fixedConfigs2.sensorRanges.TPSMaximumADC - fixedConfigs2.sensorRanges.TPSMinimumADC;


    /* Use like flags for now, just add one for each later */
    unsigned char cumulativeConfigErrors = 0;

    /* Check various aspects of config which will cause problems */

    /* BRV max bigger than variable that holds it */
    if(((unsigned long)fixedConfigs2.sensorRanges.BRVMinimum + fixedConfigs2.sensorRanges.BRVRange) > 65535){
        //sendError(BRV_MAX_TOO_LARGE);
        cumulativeConfigErrors++;
    }

    // TODO check all critical variables here!

    /*
     * check ignition settings for range etc, possibly check some of those on the fly too
     * check fuel settings for being reasonable
     * check all variable tables for correct sizing
     * etc
     */

    while(cumulativeConfigErrors > 0){
        sleep(1000);
        PORTS_BA ^= ONES16; // flash leds
        //send("There were ");
        //sendUC(cumulativeConfigErrors);
        //send(" config errors, init aborted!");
    } // TODO ensure that we can recieve config and settings via serial while this is occuring! If not a bad config will lock us out all together.
}


/* Set up all the remaining interrupts */
void initInterrupts(){
    /* IMPORTANT : Set the s12x vector base register (Thanks Karsten!!) */
    IVBR = 0xF7; /* Without this the interrupts will never find your code! */

    /* Set up the Real Time Interrupt */
    RTICTL = 0x81; /* 0b_1000_0001 0.125ms/125us period http://www.google.com/search?hl=en&safe=off&q=1+%2F+%2816MHz+%2F+%282+*+10%5E3%29+%29&btnG=Search */
//  RTICTL = 0xF9; /* 0b_1111_1001 0.125s/125ms period http://www.google.com/search?hl=en&safe=off&q=1+%2F+%2816MHz+%2F+%282*10%5E6%29+%29&btnG=Search */
    CRGINT |= 0x80; /* Enable the RTI */
    CRGFLG = 0x80; /* Clear the RTI flag */

#ifndef NO_INIT
    // set up port H for testing
    PPSH = ZEROS; // falling edge/pull up for all
    PIEH = ONES; // enable all pins interrupts
    PIFH = ONES; // clear all port H interrupt flags
#endif

    // TODO set up irq and xirq for testing
    // IRQCR for IRQ
    //

    /* VReg API setup (only for wait mode? i think so) */
//  VREGAPIR = 0x09C3; /* For 500ms period : (500ms - 0.2ms) / 0.2ms = 0b100111000011 = 2499 */
//  VREGAPICL = 0x02; /* Enable the interrupt */
//  VREGAPICL = 0x04; /* Start the counter running */
    /* Writing a one to the flag will set it if it is unset, so best not to mess with it here as it probably starts off unset */

    /* LVI Low Voltage Interrupt enable */
    VREGCTRL = 0x02; // Counts bad power events for diagnosis reasons
}

---